Use las llaves de cinta para tubo plástico, filtros o cualquier superficie resbaladiza o lisa. Las llaves de cinta también funcionan bien sobre perfiles irregulares. La cinta recubierta en poliéster extra resistente de Reed ofrece durabilidad, resistencia al deslizamiento y además protege el tubo plástico o de metal pulido contra rayas o deformaciónes. SW12A30, SW18A48 y SW24A72 tienen cintas extralargas para mayor efecto palanca en los diámetros grandes.
Más información: https://www.reedmfgco.com/es/products/wrenches/strap-wrenches/?utm_source=social&utm_medium=dailymotion
Encuentre un distribuidor cerca de usted: https://www.reedmfgco.com/es/where-to-buy/?utm_source=social&utm_medium=dailymotion
¡Conectemos!
Facebook: https://www.facebook.com/reedlatinoamerica
Instagram: https://www.instagram.com/reedlatinoamerica
YouTube: http://www.youtube.com/@ReedPipeTools
TikTok: https://www.tiktok.com/@reedpipetools
#ReedPipeTools #ReedLatAm #HerramientasIndustriales #latam #llaves #llavedecinta
Más información: https://www.reedmfgco.com/es/products/wrenches/strap-wrenches/?utm_source=social&utm_medium=dailymotion
Encuentre un distribuidor cerca de usted: https://www.reedmfgco.com/es/where-to-buy/?utm_source=social&utm_medium=dailymotion
¡Conectemos!
Facebook: https://www.facebook.com/reedlatinoamerica
Instagram: https://www.instagram.com/reedlatinoamerica
YouTube: http://www.youtube.com/@ReedPipeTools
TikTok: https://www.tiktok.com/@reedpipetools
#ReedPipeTools #ReedLatAm #HerramientasIndustriales #latam #llaves #llavedecinta
Category
🛠️
LifestyleTranscript
00:00R.I.T.H. presents the R.I.T.H. tape key.
00:10It is a light, portable and easy-to-use tool.
00:14Its main advantage is the strength of support
00:17that it exerts without scratching or deforming plastic or metal pipes.
00:21Its ductile iron handle and resistant polyester tape
00:26make it a durable tool,
00:28ideal for use on slippery, smooth or irregular surfaces.
00:33In addition, it can be used with tapes of various sizes
00:37to cover a greater number of diameters.
00:43To begin, we must place the pipe in the accessory where we want to attach it,
00:49first as far as our hands allow us.
00:59Once done, we will have to use the tape key to adjust the joint as much as possible.
01:06Next, we will proceed to explain the two possible techniques to use the tape key.
01:12For the first one, we must correctly locate the arc of the tool, which is the following.
01:19This arc must point in the direction in which I need to screw.
01:23In this case, the pipe must screw in this direction.
01:26Therefore, the arc will point in that direction.
01:32In this way.
01:35Then, I will run the tape around the pipe
01:39and I will place it again in the buckle, in this case, below the tool.
01:47And I will proceed to adjust.
01:50And I will proceed to adjust.
01:52Once adjusted, before using the tool, I must loosen the tape a little
01:58so that I give space to the head to turn completely.
02:03In this way.
02:09And I will proceed to turn and screw the pipe.
02:14As you can see, it is a smooth surface that holds perfectly
02:19and allows me to screw very easily and effortlessly.
02:22For the second technique, we will first pass the tape through the top of the tool,
02:30in this way, without holding anything.
02:34Once in that position, we will locate the arc in the correct position.
02:38Once in that position, we will locate the arc in the correct position.
02:41In the first technique, the tool should have been in this direction
02:45because I want to turn in this way.
02:47But for this technique, it must be done in the opposite way.
02:51In this way.
02:53I will pass the belt around the pipe
02:58and I will pass the tape through the same hole where I had inserted the first time.
03:08And I will screw in this way.
03:10Again, before I can apply pressure, I must give enough tape to the tool
03:14so that it can turn in this way.
03:19And again, I start to turn.
03:33At the end, I release the tape
03:39and I keep it for the next operation.
03:45Finally, remember that just as we inserted the tube in the accessory,
03:49the reverse process can also be done,
03:52insert the accessory in the tube,
03:54since some accessories have an irregular surface.
04:08Again, at the end of the process,
04:11release the tape and keep it for the next operation.
04:15Remember to wear gloves at all times.
04:19To know more, in the description you will find technical information
04:22and the contact of our specialists.
04:24And for more tools, do not forget to visit our website.
04:27See you in the next video.
04:38www.ottobock.com